Activity Stream

I am not sure my evohome tells me it is receiving a signal from it. I am sure it just said it had binded to the R8810 receiver and the receiver just...

That's what I'm trying to do. I go through the process and then hit bind and the evohome says the bind signal was received properly. Thing is,.I've...

Just checking you have set the evohome system devices option to appliance control opentherm bridge option.

Thank you for taking the time to reply. I've tried replacing the adaptor tonight, same one, just screwed on less tightly. I noticed the pin was...

Ok, so yesterday I made the following changes in the setup: 1. As said: my heatpump expects 2 different on/off signals; a signal with a heat...

I recently replaced a couple of radiators. At the same time I put new valves in but with one I noticed the black knob one turns to manually control...

Did you ever sort this out. I have had the exact same problem with one of our radiators and valves. The radiator was getting warm all the time even...

Thanks for the update, great it is solved!

This issue was resolved by phoning Resideo and them pushing the 19.33 firmware to my Evohome wifi controller. I set it to hot water priority (which...

When we had the room temp set before smart weather, the room would feel cold on cold days even though it said it was at the correct temp. Now on...

You want the room warmer because your perception of warmth/comfort is different based on the outside temperature and hence heat loss. Which is why a...

If the rooms are slightly draughty then this can more noticeable when the weather is very cold, so setting the temperature slightly higher can offset...

Why would one want a room at a higher temperature because it is colder outside? Surely if you have a room set at say 20c or 21c and that is what you...

I have never turned it on being dubious as to its value.

The boiler provides a useful D.9 status to show if the HW mode is on or not. Ofcourse if you are standing in front of the boiler the flashing Tap...

The smart weather seems to work fine for me. If it is colder outside, the rooms I have it set up on will got to a higher temp to help compensate for...

Can you not just turn the feature off? I have not requested the new firmware yet as I did not need or want most of the new features, but I would...

D.78 is effective only while the CYL terminals are closed (looped). And yes then, any boiler knob position is ignored and the flow temperature ramps...

Bruce, speaking to notorious on diynot, he said d.78 sets the HW flow temp *regardless of what the CH knob on front of the boiler is set to*. This...

A few weeks ago most of my zones went into warm weather saver mode because it thought it was about 17 or 18 degrees outside when in fact it was quite...

It seems to me Honeywell ought to remove the feature on the next software update (? 10 years’ time) for it can cause users to spend more in fuel than...

Only 1.5C error? Try 4-5 degrees for me. :) (At times when the temperature is rapidly increasing or decreasing - eg morning and evening with clear...

I do each morning check to see what the Control Panel thinks the outside temperature is and what it actually is. I thought before, that whilst the...

The feature is activated when the outside temperature gets close to or exceeds the room setpoint when the room temperature is already within 0.5C of...

Another advantage of Evohome and the VR65 is that you can set the HW differential on Evohome. In the VR65, the differential is always 5C with the...

I believe you have a LLH, which is probably why you have never seen the need for the partial load settings. I don't, so if the load is too high, my...

What is the purpose of d.77? I understand it allows you to lower the kW output for HW, but I've always found my boiler automatically modulates down...

This is what my VR65 connections look like. Notice there is no valves, or NTC connections. The eBUS is connected directly to the eBUS connections...