View Profile: intouch-control - Automated Home Forums

Tab Content: All; intouch-control; Friends; Photos

Older Activity
Yesterday, 03:08 PM

paulockenden replied to a thread Can a DTS92E control more than one device ? in Heating Control

Might be worth using a fan heater - on the cold setting - just to redistribute the air around the room and mix things up a bit. Only needs to be a...

see more

6 replies | 93 view(s)
Yesterday, 03:05 PM

paulockenden replied to a thread Evohome compatible with mix of HR91s and HR92s? in Heating Control

I find that (even good quality) tape tends to go yellow and leave a hard dry coating when used close to a heat source. Horses for courses. I guess...

see more

6 replies | 183 view(s)
12th December 2019, 12:22 PM

paulockenden replied to a thread Evohome compatible with mix of HR91s and HR92s? in Heating Control

A cable tie round the body might also work, and lot leave dried sticky if you want to remove it.

see more

6 replies | 183 view(s)
7th December 2019, 08:12 AM

paulockenden replied to a thread Den Automation has gone titsup in General Discussion

Yeah, but Earth is there for safety. I wasn’t convinced that “there’s no alternative” was a good reason to use it for power. I also suspect the...

see more

7 replies | 271 view(s)
5th December 2019, 03:12 PM

paulockenden replied to a thread Den Automation has gone titsup in General Discussion

I was never happy about how Den lights witches were wired. They used Earth as Neutral. Other manufacturers *could* do that, but they don't. For...

see more

7 replies | 271 view(s)
4th December 2019, 11:36 AM

paulockenden replied to a thread Den Automation has gone titsup in General Discussion

They had good WAF (wife acceptance factor). Or husband acceptance factor for one regular forum poster.

see more

7 replies | 271 view(s)
3rd December 2019, 04:34 PM

paulockenden replied to a thread Evohome controller multi comms faults. in Heating Control

That would only be true if you had HR92s on all of your rads (and an ABV). Without them, if you did as you've described, you'd have those rads...

see more

27 replies | 1031 view(s)
3rd December 2019, 04:31 PM

paulockenden started a thread Den Automation has gone titsup in General Discussion

According to The Register (who are usually right about these things), Den Automation has gone to the wall. It's a shame - the products had a lot...

see more

7 replies | 271 view(s)
30th November 2019, 04:33 PM

paulockenden replied to a thread Intergas Diagnostic Software S1-S5 temperatures in Heating Control

There's an option sensor that you can connect to the DHW incoming (I use it as I have a pre-heat tank). Perhaps it's that? Difficult to know...

see more

5 replies | 244 view(s)
27th November 2019, 10:28 AM

paulockenden replied to a thread Do you think there'll be a new Evo panel coming? in Heating Control

That's what wireshark is for! The bigger problem will be certificates. Assuming this stuff is properly secure. Which might not be a good...

see more

15 replies | 663 view(s)
25th November 2019, 02:43 PM

paulockenden replied to a thread RAMSES protocol but not Honeywell in Heating Control

Very interesting. That kit is REALLY useful if you have damp issues in your home. Also good for landlords to fit in rentals. Doesn't look like...

see more

2 replies | 272 view(s)

No More Results

intouch-control
Automated Home Lurker

Mini Statistics

More 1 Friend

paulockenden

Recent Visitors

Basic Information

About intouch-control

Contact

Statistics

Total Posts

General Information

1 Friend

paulockenden

intouch-control Automated Home Lurker

Mini Statistics

More 1 Friend

paulockenden

Recent Visitors

Basic Information

About intouch-control

Contact

Statistics

Total Posts

General Information

1 Friend

paulockenden

intouch-control
Automated Home Lurker