Hello all
Just joined so apologies if this is in the wrong place.
Wife and I are getting on a bit so need the heating! Sorry if this sounds long-winded.
System is open vented according to Google(cold tank in loft....)
House: 3 bedroom bungalow with 1 bathroom + 1 en-suite. 9 radiators: Living, dining, kitchen, hall, 3x bedrooms, en-suite, bathroom.
Previous System when we bought house 1987: Potterton Ep2000 in utility room, Unknown Boiler in hall cupboard, Honeywell Thermostat in hall.
System now: Potterton Ep2, Worcester Bosch Greenstar r24i, Danfoss thermostat all in same locations.
In 2007 we had the boiler replaced along with all radiators except the living room one, system drained etc etc.
Few niggly problems with boiler initially but soon settled down.
We had intermittent small problems, mostly fixed in a timely manner by our local contractor(we have a monthly contract).
One small niggly problem persisted in that the boiler would not fire when it should have i.e. the house was getting bloody cold! I suspected the controller!?
In October 2013 a qualified electrician replaced the original Potterton Ep2000 with a wiring compatible Ep2.
The problem persists which is basically - the boiler does not always fire when the radiators get progressively colder and Mrs complains she is freezing. Hall thermostat set at 24 and even turning it to MAXIMUM does NOT cause the boiler to fire. Programmer CH light is ON, Hall Thermostat Green and Red lights are ON, Boiler Blue light is ON, Pump Green light is ON, but the boiler does not fire.
HOW I WORK AROUND IT AND TO DATE IT HAS ALWAYS WORKED:
1. Turn Programmer HW light(if it is on) by pressing the ADV button.
2. Switch Programmer OFF at the adjacent wall switch and count to 10.
3. Switch programmer ON which means it comes on with ONLY THE CH light ON.
4. Boiler fires almost immediately and Mrs soon happy and warm again.
Just had the annual boiler maintenance done. Mentioned problem to contract who reckoned the problem COULD be that the HW was set to come on along with the CH for the same length of time which is 06:15 - 09:30 and 16:00 - 21:30. Any other heating(ONLY) outwith those times initiated by press the Programmer ADV button.
Anyway, the problem persists and I am reluctant to go ahead with an expensive Evohome purchase/professional install(£740 for parts plus installation).
Regards
Just joined so apologies if this is in the wrong place.
Wife and I are getting on a bit so need the heating! Sorry if this sounds long-winded.
System is open vented according to Google(cold tank in loft....)
House: 3 bedroom bungalow with 1 bathroom + 1 en-suite. 9 radiators: Living, dining, kitchen, hall, 3x bedrooms, en-suite, bathroom.
Previous System when we bought house 1987: Potterton Ep2000 in utility room, Unknown Boiler in hall cupboard, Honeywell Thermostat in hall.
System now: Potterton Ep2, Worcester Bosch Greenstar r24i, Danfoss thermostat all in same locations.
In 2007 we had the boiler replaced along with all radiators except the living room one, system drained etc etc.
Few niggly problems with boiler initially but soon settled down.
We had intermittent small problems, mostly fixed in a timely manner by our local contractor(we have a monthly contract).
One small niggly problem persisted in that the boiler would not fire when it should have i.e. the house was getting bloody cold! I suspected the controller!?
In October 2013 a qualified electrician replaced the original Potterton Ep2000 with a wiring compatible Ep2.
The problem persists which is basically - the boiler does not always fire when the radiators get progressively colder and Mrs complains she is freezing. Hall thermostat set at 24 and even turning it to MAXIMUM does NOT cause the boiler to fire. Programmer CH light is ON, Hall Thermostat Green and Red lights are ON, Boiler Blue light is ON, Pump Green light is ON, but the boiler does not fire.
HOW I WORK AROUND IT AND TO DATE IT HAS ALWAYS WORKED:
1. Turn Programmer HW light(if it is on) by pressing the ADV button.
2. Switch Programmer OFF at the adjacent wall switch and count to 10.
3. Switch programmer ON which means it comes on with ONLY THE CH light ON.
4. Boiler fires almost immediately and Mrs soon happy and warm again.
Just had the annual boiler maintenance done. Mentioned problem to contract who reckoned the problem COULD be that the HW was set to come on along with the CH for the same length of time which is 06:15 - 09:30 and 16:00 - 21:30. Any other heating(ONLY) outwith those times initiated by press the Programmer ADV button.
Anyway, the problem persists and I am reluctant to go ahead with an expensive Evohome purchase/professional install(£740 for parts plus installation).
Regards
Comment