Search:

Type: Posts; User: roydonaldson

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. A good idea, but definately a lazy...

    A good idea, but definately a lazy implementation. The time on the device should be accurate, but the offset should then be being applied to the sending api. I do understand the challenge, having...
  2. I just ordered a new set of 4 AA rechargeables to...

    I just ordered a new set of 4 AA rechargeables to see if starting with some fresh ones will help.

    Roy.
  3. Thanks. Good to know. Whew.

    Thanks. Good to know. Whew.
  4. So, that's now both Saturday and Sunday on my...

    So, that's now both Saturday and Sunday on my controller setting my bedrooms to 35C. Today, Monday, it all seemed ok, but, I may simply not have been up in time to see it early on.

    Roy.
  5. I have no heat in the downstairs of my house. All...

    I have no heat in the downstairs of my house. All downstairs zones are below there setpoints, EvoHome controller shows all these zones calling for 100% heat, yet the BDR91 zone valve at the boiler is...
  6. Just got up this morning to find Bedroom Zone set...

    Just got up this morning to find Bedroom Zone set to 35C.......and Living Room set to 19C, reading 15.5C, zone says calling for 100% heat, and yet Zone Valves are off and not pumping at boiler....
    ...
  7. Actually, this was exactly what I was thinking....

    Actually, this was exactly what I was thinking. Last night EvoHome increased me zone temps as it was colder outside, but..it was completely still and didn't feel cold. I tend to find that my house...
  8. Andy, I have a house with 2 zone valves, ie. I...

    Andy, I have a house with 2 zone valves, ie. I have a larger house with it setup as upstairs and downstairs controlled by these zone valves. Having something such as Load Scaling would be beneficial...
  9. Replies
    5
    Views
    720

    I've created a 'Custom Program' for just that....

    I've created a 'Custom Program' for just that. It's set to a couple of degrees higher than the normal program. I just activate it if I feel a bit chilly around the house.
  10. Replies
    14
    Views
    1,639

    I've used Lithium batteries before, but only for...

    I've used Lithium batteries before, but only for locations that were difficult to access. I'd consider just buying a pack of standard AA's and going for those. Have a look at these for instance:
    ...
  11. Replies
    5
    Views
    1,167

    I just measured it out on google maps, they'd be...

    I just measured it out on google maps, they'd be about 450m away from the house. House alarm reports:

    RF Jamming: 15:37
    RF Jamming Restore: 15:39
    RF Jamming: 16:23
    RF...
  12. Replies
    5
    Views
    1,167

    RF interference ?

    Interesting one yesterday, I was walking past my alarm control panel and it had a red light on and was saying 'Jamming', I cleared it down a couple of times and then didn't think too much of it. I...
  13. A trick you can use if this is the case. If you...

    A trick you can use if this is the case. If you are not using the EvoHome controller internal sensor, set the sensor for the electric zone to be the EvoHome internal sensor and then use +35C for On...
  14. I'm not actually using it to heat the bathroom...

    I'm not actually using it to heat the bathroom up. It already has 2 large radiators in it and I'm simply using the EUF heating to warm the floor tiles. As such, I'm happy for it to be on for 45...
  15. Does anyone know if Optimisation is being applied...

    Does anyone know if Optimisation is being applied to Electric Heating Zones ?

    It would be expensive if it started bringing them on up to 3 hours earlier if you didn't want them on that early.
    ...
  16. Replies
    6
    Views
    1,542

    All working. Toasty warm this morning. It's...

    All working. Toasty warm this morning.

    It's amazing what a bit of not being tired and actually reading the wiring diagram can do :-)
  17. Replies
    6
    Views
    1,542

    Only about 4/500 watts. Definitely under 1k. ...

    Only about 4/500 watts. Definitely under 1k.

    Roy
  18. Replies
    6
    Views
    1,542

    So, both Neutrals in to N. Perm live into left L,...

    So, both Neutrals in to N. Perm live into left L, link between right L and A. Then switched out (live) into B.

    I guess both Ls are connected together in the box itself ?
  19. Replies
    6
    Views
    1,542

    Wiring BDR91 as simple on/off relay

    I'm sure I'm just tired, but instead of reading all the wiring manuals again I thought I'd just ask here.

    I'm going to use a BDR91 as a simple on/off relay to turn my electric heating on.

    I've...
  20. Updated and all working.

    Updated and all working.
  21. Any ideas when the firmware will be being pushed...

    Any ideas when the firmware will be being pushed out to us ?
  22. Replies
    21
    Views
    4,709

    Any ideas when they will be pushing the update...

    Any ideas when they will be pushing the update out to us ?
  23. Email sent off

    Email sent off
  24. Perhaps good to let customer support know that...

    Perhaps good to let customer support know that there is a new release:

    "Dear Mr. Donaldson,

    I have received the confirmation that there is no V2 firmware.
    We have checked in the system and you...
  25. I'm guessing it's overshooting as it's not...

    I'm guessing it's overshooting as it's not getting any time to learn the charactristics of the room and boiler. If it gets turned on and it's cold outside and low temp to begin with and boiler is...
Results 1 to 25 of 194
Page 1 of 8 1 2 3 4