Search:

Type: Posts; User: bruce_miranda

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. I had to use terminal 7-8-9 in order to get my...

    I had to use terminal 7-8-9 in order to get my OTB to fire the boiler. And because that is undocumented, until I figured it out, I had to use the 240V trigger to fire the boiler and my VR33/OTB were...
  2. I'm guessing this interface can only monitor the...

    I'm guessing this interface can only monitor the OT traffic, it cannot actually inject or alter a command? That would require a gateway?
  3. Replies
    3
    Views
    285

    Or just delete the location and repair the...

    Or just delete the location and repair the installation to the app.
  4. Care to share your circuit and code?

    Care to share your circuit and code?
  5. Replies
    27
    Views
    2,295

    What is the HW Over run set to? Also when you saw...

    What is the HW Over run set to? Also when you saw the HW temp go beyond the set point, what was the actual Heat Demand for the HW in the settings menu
  6. I have a single pocket too, and just pushed my...

    I have a single pocket too, and just pushed my evohome sensor into the same pocket. Seemed to fit even with the wires of the previous sensor and Evohome is happy.
  7. Replies
    3
    Views
    530

    I built my own diverter because the off the shelf...

    I built my own diverter because the off the shelf products all had too many compromises. Having something I could tweak has allowed me to tune my diverter to the point that I have exported next to...
  8. Replies
    3
    Views
    530

    I use a Solar diverter but it doesn't use a...

    I use a Solar diverter but it doesn't use a temperature sensor, it doesn't need to. It keeps heating the cylinder via the immersion heater, until the immersion heater thermostat has cut off and once...
  9. DHW set point can be changed but not via the API....

    DHW set point can be changed but not via the API. You can only do that via the radio.
    Temporary Override Until is actually the exact way how Resideo implemented the HW Boost. So when you select...
  10. Replies
    27
    Views
    2,295

    My CS92 does not use batteries any more. And yet...

    My CS92 does not use batteries any more. And yet it will show a comms failure every so often.
    And because I have a log of absolutely every Evohome RF message, it is quite easy for me to go and have...
  11. Replies
    8
    Views
    856

    Because I have the ability to raise the Flow...

    Because I have the ability to raise the Flow temperature when heating the HW cylinder, I used to time the HW recharge to when the house was the coldest I.e. First thing in the morning and then around...
  12. Replies
    8
    Views
    856

    I guess this completely depends on the usage of...

    I guess this completely depends on the usage of your HW. I doubt there is an ideal setting. The one feature I do love in the Evohome wrt HW is Differential. That allows the water temp to drop by that...
  13. Replies
    27
    Views
    2,295

    The frequency of the comms failure messages is...

    The frequency of the comms failure messages is inversely proportionate to the numbers of messages the CS92 sends the controller. Changing, repositioning the batteries etc, just forces the CS92 to...
  14. Replies
    27
    Views
    2,295

    https://www.automatedhome.co.uk/vbulletin/showthre...

    https://www.automatedhome.co.uk/vbulletin/showthread.php?6366-Introducing-the-HGI80-alternative-the-latest-DIY-kid-on-the-block&p=45562&viewfull=1#post45562
  15. Replies
    27
    Views
    2,295

    I think the proper solution is not software only...

    I think the proper solution is not software only but needs a different hardware platform. But you are right, the SSM with evofw3 is an ideal platform to extend to add a temperature sensor to that can...
  16. Replies
    27
    Views
    2,295

    A mains powered CS92 option would have been ideal...

    A mains powered CS92 option would have been ideal especially as the likelihood of there being a power source in the vicinity of the HW tank is quite high. Nevertheless, the issue isn't with the CS92...
  17. Replies
    27
    Views
    2,295

    You tend not to get Comms faults when the HW is...

    You tend not to get Comms faults when the HW is actually on a lot. The issue is that the Controller will sometimes go deaf to the message sent by the CS92 and then marks it as Unavailable with a...
  18. Replies
    27
    Views
    2,295

    I run the CS92 and the Evohome controller off the...

    I run the CS92 and the Evohome controller off the same wall mount PSU. So my CS92 doesn't use any batteries. I did this to test if it was the batteries causing the community failures. Ofcourse we now...
  19. If you are seeing absolutely nothing move in the...

    If you are seeing absolutely nothing move in the Device manager as you plug this in, then check.
    a. Are you actually plugging this in the right way around in the USB socket
    b. Do you see any LED...
  20. I think they tried to do this via the Quick...

    I think they tried to do this via the Quick Actions. But since most of them have designated functions, the only real option remaining is Custom, but then there is only 1 of them.
  21. Replies
    2
    Views
    378

    You changed the batteries to new chargeable...

    You changed the batteries to new chargeable batteries?
  22. The All Sensors is not needed if you are only...

    The All Sensors is not needed if you are only interested in the sensors that Evohome recognises. E.g. The HR92 has a sensor and actuator. But if you are using a wall temperature sensor in addition to...
  23. Correct, a heating system, like life, is full of...

    Correct, a heating system, like life, is full of compromises.
  24. Yes, the lower the floor the better. You are...

    Yes, the lower the floor the better. You are probably never going to need the boiler at full pelt with Evohome. OT does help, a bit because it alters the flow temperature required as well.
  25. And this causes all sorts of fun between you and...

    And this causes all sorts of fun between you and your heating engineer, who is still using whole house heat loss calculations but in an Evohome system, you are almost never heating the whole house....
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4