Search:

Type: Posts; User: petep

Search: Search took 0.02 seconds.

  1. Replies
    153
    Views
    40,707

    @smar. What firmware are you running. If my FIFO...

    @smar. What firmware are you running. If my FIFO branch do you have OT?
  2. Replies
    153
    Views
    40,707

    Do you have an OT module in your system? If so...

    Do you have an OT module in your system?

    If so are you seeing messages?
  3. Replies
    153
    Views
    40,707

    Which code are you running on the nano?

    Which code are you running on the nano?
  4. Replies
    13
    Views
    2,200

    Somewhat lucky there, it runs the length of the...

    Somewhat lucky there, it runs the length of the loft and then goes down the corner of a bedroom which is above a garage. Hid the run through that room by adding a very narrow stud+plasterboard to...
  5. Replies
    13
    Views
    2,200

    See my comment above My boiler is in the...

    See my comment above


    My boiler is in the loft on one side of the house. My UFH is on the ground floor on the other side. It' couldn't be further away


    That's irrelevant. The Controller...
  6. Replies
    13
    Views
    2,200

    For clarification the feed/return for the UFH in...

    For clarification the feed/return for the UFH in my system branches near the boiler close to the CH zone valve. It's not part of the rad loop.
  7. Replies
    10
    Views
    1,824

    I had a phantom zone I deleted the location on...

    I had a phantom zone

    I deleted the location on the Honeywell Server and added it back again and all was well.
    (I read this somewhere on one of the threads)
  8. Replies
    13
    Views
    2,200

    For what it's worth my original system was s-plan...

    For what it's worth my original system was s-plan DHW + CH with zone valve for each driving boiler.

    A couple of years ago I added a 2 zone UFH in an extension

    The UFH controller (not H/well)...
  9. Replies
    153
    Views
    40,707

    Just got back from a longer than expected trip to...

    Just got back from a longer than expected trip to Dublin (thank you, Beast from the East and Emma)

    I've only got the RX side of the code changes working so far but think I'm seeing fewer problems...
  10. Replies
    153
    Views
    40,707

    @dty's evofw2 requires minimal changes. I had...

    @dty's evofw2 requires minimal changes.

    I had to modify config.h and Makefile and write a new hw/<target>.h file

    Since your stick has a different adapter board between the nano and cc1101 it's...
  11. Replies
    153
    Views
    40,707

    That's effectively what my stick is as well. The...

    That's effectively what my stick is as well. The only difference being the carrier board used to attach the CC1101 to the nano. That's the bit that's not obviously available to buy separately or...
  12. Replies
    153
    Views
    40,707

    @TomJ yes mine is running at 16MHz. Can run...

    @TomJ

    yes mine is running at 16MHz.
    Can run the USB comms at 115200 (tested for a few minutes at 250000!)

    I don't have an OT module so can't comment on those problems

    I'm looking to see if...
  13. Replies
    153
    Views
    40,707

    @dty I've got the nano plugged into my pi and...

    @dty

    I've got the nano plugged into my pi and I've set up ser2com

    Running Domoticz 3.8153 on Synology.

    How do I connect the "HGI80"?
    I can't work out how to set up the "serial port"...
  14. Replies
    153
    Views
    40,707

    I've only been able to log for a few days but so...

    I've only been able to log for a few days but so far all the messages from the controller setting the broadcast period look like this
    --- I --- 01:140959 --:------ 01:140959 1F09 003 FF0898...
  15. Replies
    153
    Views
    40,707

    So it appears TX was working all the time ;) I...

    So it appears TX was working all the time ;)

    I think the problem was that nothing else was prepared to do RX.

    Scanning my RX log I came across an interesting feature around 4 am every day.
    All...
  16. Replies
    153
    Views
    40,707

    @dty it appears you're exceeding your stored...

    @dty it appears you're exceeding your stored private message quota :-)



    I'm currently running Domoticz on a Synology and I have all the USB ports in use :-( Planning to switch it to a pi I've...
  17. Replies
    153
    Views
    40,707

    I've just bought myself one of these...

    I've just bought myself one of these
    [https://www.smarthome-agentur.de/produkt/nanocul-868-mhz-premium-aktuelle-fw-ftdi-cc1101-sma-transceiver-cul-stick-fuer-fhem/ ~42 euro delivered in 2-3 days...
Results 1 to 17 of 17