Cheers Paul, I am going to get an installer to have a look at my whole system and see if he can figure out what is going on. I will put your suggestion to him.
Thanks
Will
Type: Posts; User: willdonal
Cheers Paul, I am going to get an installer to have a look at my whole system and see if he can figure out what is going on. I will put your suggestion to him.
Thanks
Will
Thanks Mate, Electrical work is not my forte so I guess it is time to get the pro's in. Thanks for your time in trying to sort this out for me and I know it must be quite frustrating when you see the...
Here are the pictures. The first one shows the CS92 connected to the hot water cylinder, the second is the heating BDR, the third is the Hot water BDR and the last one is where the wires all go in to...
Hello DBMandrake, Can we just go back to basics please. I set up my hot water first and part of the process is the controller asks you what sort of system you have. I have tried both options, eg 2 or...
Well I spoke to soon again. Hot water came on along with the heating. When you say you do not bond a boiler relay, I can’t get the heating to work without doing it. I can get the hot water to work...
Thanks mate. Not sure how it is wired up, but the way I have it now it seems to work. I have hot water when required and the heating comes on when requested. When I first got the system I...
Thanks DBmandrake and dty, I tried to set it up with no boiler selected when setting up the water and in the boiler control selected none. As I suspected the controller sent a signal to the TRv's and...
Thanks for that. I also have 3 zones but in my case it was zone 1 - heating downstairs, zone 2 - Heating upstairs and zone 3 - Hot water. It has been wired up now so it is just Heating and hot water....
Hi all, thought I had sussed it. Got no fault reported on the controller and heating and water was working as it should, or so I thought. The hot water is set to come on at 5pm and Ive just gone in...
Thanks Paul, I will try what dty said and see how we go
Will
Thanks dty, Yes that is how my system is set up, 1 BDR for the hot water and one BDR for the heating with a hot water cs92 connected to the hot water tank. I will try setting it up again without the...
Hi, thanks for the reply. I have 1 BDR to control the water, eg to turn the boiler on to heat the water and another BDR to turn the boiler on for the heating. Would I not require the 2 BDR's to...
Hi, yes I did the old press for 15 seconds till it flashed quickly then 5 seconds to make it flash slowly, then did the bonding
Thanks for the reply. Originally the BDR's were side by side as the installer hadn't read the installation procedure properly. I then got an official Honeywell installer to come down and sort it out....
Spoke to soon, Heating coming on, or should I say the heating BDR is turning on when the hot water BDR comes on :-( :-(
OK, in case any other member has a problem like mine I have managed to fix it by doing a complete factory reset and rebonding 14 HR92, 2 x BDR91 and the cs92. Had to do it twice as the first time the...
Update, after an hour the green light went off :-) :-)
Hello guys, I have had my system installed for nearly 2 years now and for most of it it works flawlessly. I even have it integrated in to Alexa :-) :-)
Since day one though I have always been...
Thanks Hengus, I'll bear them in mind. Cheers
Certainly not at the temperature mine is at :o :o :o
OK Thanks, I'll leave it to the expert next week. Cheers :-) :-)
Got you, I'll dig out the manual for the boiler. If I turned down the brass Knob would that not reduce the max temp the tank would get to before it switched off. Or the blue dial? thanks
The last reply the pictures didn't work for some reason so i'll try again here 10931094
There is a brass screw with numbers beside it and another dial with no numbers. Which one do I adjust?
10911092
Ok will do , Thanks for your input :-) :-)