Search:

Type: Posts; User: roydonaldson

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    642

    I've created a 'Custom Program' for just that....

    I've created a 'Custom Program' for just that. It's set to a couple of degrees higher than the normal program. I just activate it if I feel a bit chilly around the house.
  2. Replies
    14
    Views
    1,475

    I've used Lithium batteries before, but only for...

    I've used Lithium batteries before, but only for locations that were difficult to access. I'd consider just buying a pack of standard AA's and going for those. Have a look at these for instance:
    ...
  3. Replies
    5
    Views
    1,018

    I just measured it out on google maps, they'd be...

    I just measured it out on google maps, they'd be about 450m away from the house. House alarm reports:

    RF Jamming: 15:37
    RF Jamming Restore: 15:39
    RF Jamming: 16:23
    RF...
  4. Replies
    5
    Views
    1,018

    RF interference ?

    Interesting one yesterday, I was walking past my alarm control panel and it had a red light on and was saying 'Jamming', I cleared it down a couple of times and then didn't think too much of it. I...
  5. A trick you can use if this is the case. If you...

    A trick you can use if this is the case. If you are not using the EvoHome controller internal sensor, set the sensor for the electric zone to be the EvoHome internal sensor and then use +35C for On...
  6. I'm not actually using it to heat the bathroom...

    I'm not actually using it to heat the bathroom up. It already has 2 large radiators in it and I'm simply using the EUF heating to warm the floor tiles. As such, I'm happy for it to be on for 45...
  7. Does anyone know if Optimisation is being applied...

    Does anyone know if Optimisation is being applied to Electric Heating Zones ?

    It would be expensive if it started bringing them on up to 3 hours earlier if you didn't want them on that early.
    ...
  8. Replies
    6
    Views
    1,337

    All working. Toasty warm this morning. It's...

    All working. Toasty warm this morning.

    It's amazing what a bit of not being tired and actually reading the wiring diagram can do :-)
  9. Replies
    6
    Views
    1,337

    Only about 4/500 watts. Definitely under 1k. ...

    Only about 4/500 watts. Definitely under 1k.

    Roy
  10. Replies
    6
    Views
    1,337

    So, both Neutrals in to N. Perm live into left L,...

    So, both Neutrals in to N. Perm live into left L, link between right L and A. Then switched out (live) into B.

    I guess both Ls are connected together in the box itself ?
  11. Replies
    6
    Views
    1,337

    Wiring BDR91 as simple on/off relay

    I'm sure I'm just tired, but instead of reading all the wiring manuals again I thought I'd just ask here.

    I'm going to use a BDR91 as a simple on/off relay to turn my electric heating on.

    I've...
  12. Updated and all working.

    Updated and all working.
  13. Any ideas when the firmware will be being pushed...

    Any ideas when the firmware will be being pushed out to us ?
  14. Replies
    21
    Views
    4,245

    Any ideas when they will be pushing the update...

    Any ideas when they will be pushing the update out to us ?
  15. Email sent off

    Email sent off
  16. Perhaps good to let customer support know that...

    Perhaps good to let customer support know that there is a new release:

    "Dear Mr. Donaldson,

    I have received the confirmation that there is no V2 firmware.
    We have checked in the system and you...
  17. I'm guessing it's overshooting as it's not...

    I'm guessing it's overshooting as it's not getting any time to learn the charactristics of the room and boiler. If it gets turned on and it's cold outside and low temp to begin with and boiler is...
  18. Replies
    106
    Views
    24,949

    I do have sympathy for Honeywell here. If you...

    I do have sympathy for Honeywell here. If you think back a few years ago, a heating controller was a microprocessor device that was installed by a heating engineer and just left to work. If you think...
  19. Replies
    6
    Views
    1,867

    Just use the Custom setting and build one...

    Just use the Custom setting and build one yourself. I've got my Custom setting to turn all of the downstairs rooms on to 21. You can hit it once to enable it, or hold it down to turn it on for a...
  20. Replies
    106
    Views
    24,949

    Tha's slightly different. Most devices nowadays...

    Tha's slightly different. Most devices nowadays have a button that then shows the current firmware release and another botton on that same page that says 'check for update', you press that and it...
  21. Replies
    106
    Views
    24,949

    May be worth a feature request. Add a About...

    May be worth a feature request. Add a About button in to Settings, that shows the current firmware. Holding down a button for ages is such an old fashioned way to do it.
  22. Still at: App 01.00.07.01 WiFi 01.00.06.10...

    Still at:

    App 01.00.07.01
    WiFi 01.00.06.10

    Wonder what's changed ??
  23. Replies
    77
    Views
    10,279

    You really need to make sure that you keep the...

    You really need to make sure that you keep the hot water temperature stored above 45. Have a read at:

    https://www.ncbi.nlm.nih.gov/pmc/articles/PMC2094925/
    ...
  24. Replies
    77
    Views
    10,279

    I had this exact problem when I put my EvoHome...

    I had this exact problem when I put my EvoHome system in. I thought I had the valve adaptor seated corrrectly, but didn't. When any room would call for heat, the main livig room radiator would heat...
  25. Replies
    31
    Views
    11,501

    Any update on when this may be coming ?

    Any update on when this may be coming ?
Results 1 to 25 of 186
Page 1 of 8 1 2 3 4