Search:

Type: Posts; User: ajaxuk

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    4,272

    Poll: I have a conventional alarm, but would like to...

    I have a conventional alarm, but would like to gradually start using cortex. My Idratek install is still in it's infancy and I don't have enough sensors to replace my current system.
  2. Replies
    28
    Views
    24,134

    I have .Net 2.0 installed, but keep getting the...

    I have .Net 2.0 installed, but keep getting the following error message:

    "Error 1001. The account name is invalid or does not exist, or the password is invalid for the account name specified."
    ...
  3. Thread: usb to serial

    by ajaxuk
    Replies
    34
    Views
    18,112

    That would make things a lot easier in terms of a...

    That would make things a lot easier in terms of a wider range of hardware.
  4. Replies
    28
    Views
    24,134

    Thanks Kevin for this writeup, I followed it all...

    Thanks Kevin for this writeup, I followed it all the way through and have pretty much got it working, with a couple of little hiccups along the way.

    I couldn't install xFx Express Hub on my...
  5. Thread: DFP unboxed

    by ajaxuk
    Replies
    12
    Views
    10,159

    Kevin I believe there will be updates in...

    Kevin

    I believe there will be updates in Cortex v24 to address the key lighting.
  6. Thread: DFP unboxed

    by ajaxuk
    Replies
    12
    Views
    10,159

    Nice pictures Paul. I set up my display...

    Nice pictures Paul.

    I set up my display yesterday but unfortunately I seem to have "lost" my phone (camera) so couldn't post any pictures.

    It was my first Idratek order so I have been busy this...
  7. Replies
    10
    Views
    7,046

    I'm awaiting my first Idratek order :)

    I'm awaiting my first Idratek order :)
  8. Replies
    10
    Views
    11,602

    Job done!... well 1st of many:) I managed to...

    Job done!... well 1st of many:)

    I managed to break the plasterboard, which you can see in the top right of the second photo. Luckily SWMBO hasn't noticed yet, so will postpone fixing 'til she...
  9. Replies
    10
    Views
    11,602

    Thanks Andrew, I think they would serve well for...

    Thanks Andrew, I think they would serve well for the standard modules.

    Yesterday I started the drilling / chiselling process ready for my first DFP when it arrives. I would say that it is a lot...
  10. Thread: Dfp-h02

    by ajaxuk
    Replies
    12
    Views
    7,510

    They've updated the price list on the website. ...

    They've updated the price list on the website.

    228.
  11. Thread: Dfp-h02

    by ajaxuk
    Replies
    12
    Views
    7,510

    Looks much nicer than the last panel imo.

    Looks much nicer than the last panel imo.
  12. Replies
    10
    Views
    11,602

    Thanks for all the replies. Looks like i'm...

    Thanks for all the replies.

    Looks like i'm going to have to go the pre-drill and then hammer and chisel route.

    Mark
  13. Replies
    10
    Views
    11,602

    Thanks for your reply Gumby. I am looking to...

    Thanks for your reply Gumby.

    I am looking to install the new display panels



    and possibly a few single dimmer switches SLD002. Additonal sensors if needed will probably go in the ceiling...
  14. Replies
    10
    Views
    11,602

    25mm pattress box

    I've just measured the depth of the pattress's in my new house and they all appear to be 25mm deep and they sit flush against the concreted wall blocks.

    Considering the idratek datasheets specify...
  15. Replies
    4
    Views
    6,988

    Scantronic Alarm & Cortex

    I've just purchased a new home and have inherited a wired alarm system with the typical selection of PIR's, a door contact and panic buttons. It's the Scantronic 9651.

    I'm at the planning stage at...
  16. Replies
    19
    Views
    36,271

    I'm moving into my new house next week and am...

    I'm moving into my new house next week and am going to have to retrofit everything, so I think I will try out the Y-cam Black with outdoor enclousre as well as the D-link PoE adatper...
  17. Replies
    19
    Views
    36,271

    I have been tempted by these: ...

    I have been tempted by these:

    http://www.y-cam.com/products.php

    However it doesn't meet the powered over ethernet criteria. Also I would have preferred an ethernet only version.

    Price and...
Results 1 to 17 of 17