Search:

Type: Posts; User: therealfronty

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. I thought I read something something that said...

    I thought I read something something that said the HR92's cycle once every week or two precisely to prevent valve stickyness.
  2. Replies
    8
    Views
    1,776

    Do you have a microwave oven? If so try...

    Do you have a microwave oven? If so try unplugging it from the mains, leave it a day or so and see if that helps.

    Do you have anything else apart from your internet WiFi that uses wireless...
  3. Replies
    6
    Views
    1,000

    I logged a ticket with Resideo and they came back...

    I logged a ticket with Resideo and they came back with quite a comprehensive reply, interesting comment about the antenna orientation on the HR92...

    Good afternoon,

    Thank you for contacting...
  4. Replies
    6
    Views
    1,000

    Had this again this afternoon, all zones showing...

    Had this again this afternoon, all zones showing 0% demand, yet the boiler was firing every 10 mins and then cutting out because I only had my bypass bathroom radiator to dissipate the heat, it was...
  5. Replies
    1
    Views
    358

    T87RF fixings

    Hi all, I bought a couple of T87RF off ebay but they didn't come with any wall fixings, it looks like they need quite a thin screw or self-tapper, and associated rawplug, but I can't find anything...
  6. I replaced it with a spare I had and have had no...

    I replaced it with a spare I had and have had no problems since, so I'm guessing this one is faulty, it was part of a cheap job lot off ebay so not too bothered.
  7. Replies
    108
    Views
    14,033

    Maybe they should rename it Evohope lol FWIW...

    Maybe they should rename it Evohope lol

    FWIW I've had my hot water kit installed for about a month now and not had any issues, it's running on the batteries it was supplied with. Must admit it's...
  8. T87RF crashes when temp reaches 32 degrees

    Something weird going on here, it's been getting a little toasty in our conservatory and three times now the evotouch panel has reported a sensor error. I use a T87RF to get a more accurate...
  9. Replies
    4
    Views
    459

    Hmm I was just wondering if you could use a...

    Hmm I was just wondering if you could use a normal BRD91 but wire the fan using the normally closed contacts instead of the normally open (A & C).

    So lets say the set point is 20 degrees, but it's...
  10. Welcome to the wonderful world of spurious heat...

    Welcome to the wonderful world of spurious heat demands! I've given up checking now when this happens to me, I hear the boiler fire and think "what zone is that?". It's a bit of a faff having to go...
  11. Replies
    1
    Views
    401

    Finished at last

    Finally finished my Evohome installation, it looks great now the evotouch panel is mounted on the wall, looks really classy...

    1816

    1817
  12. I requested the update by logging a support...

    I requested the update by logging a support ticket here, I'm not sure why they don't push out updates automatically, it might be so they don't "upset" customers when things unexpectedly change (eg...
  13. Replies
    6
    Views
    1,000

    Boiler firing with little or no demand

    I've read a lot about issues here to do with the boiler firing when there is apparently no demand and missing RF messages etc., but evohome really does appear to do some odd things sometimes. I'm...
  14. So would the solution be to reduce the resistance...

    So would the solution be to reduce the resistance by opening all TRVs and all the lockshield valves? If it works and the boiler stays lit then it's a case of slowly rebalancing all the rads? - it...
  15. Replies
    13
    Views
    1,568

    I've only had evohome installed for a few weeks...

    I've only had evohome installed for a few weeks now, so I'm not going to see any benefit until the colder nights start creeping in, but what I have noticed is that the odd room will call for heat as...
  16. Grundfos alpha pump too slow on autoadapt, CP or PP settings

    I remember seeing some chatter, it might have been on another forum, about the auto-adapt and CP/PP modes on these Alpha 2 pumps, in the end I and others ended up using one of the fixed speed modes...
  17. The wife wonders why I never throw anything out,...

    The wife wonders why I never throw anything out, "Ooooh I think I've got an old bit of wire in the garage that'll do that.... voila!" :cool:
  18. Yeah I ended up doing the same when I wired in a...

    Yeah I ended up doing the same when I wired in a BDR91. 🙂
  19. Replies
    1
    Views
    301

    HR92 dial not working

    I have an HR92 here that won't change menus when I turn the dial on top, it feels "clicky" when you turn it, like the rest of the ones I've got, and I've taken it apart to see what's going on, the...
  20. Adding Evohome CH & DHW BDR91s to old Sundial Y-Plan wiring centre

    Hi all,

    So I've been having a good old play up in the airing cupboard today and got both my Evohome BDR91s now controlling the DHW and CH. I didn't want to do too much re-wiring so left the...
  21. Oh I think I have answered my own question, good...

    Oh I think I have answered my own question, good grief, the earth is wired up to the common terminal.

    1811

    1812
  22. Replacing cylinder stat with CS92 - confused by old connection

    I was having a look in my wiring centre today to take a look at how the old cylinder stat was wired up (an L641A). I was thinking I could just replace these connections with the switched relay...
  23. Replies
    4
    Views
    526

    Just do the RF check for that zone, it will send...

    Just do the RF check for that zone, it will send a message and report it as unsuccessful (because the HR92 didn't respond), then I'm pretty sure it gives you the option to delete it. Try that first....
  24. Replies
    4
    Views
    526

    Hi, I have done this, you definitely don't need...

    Hi, I have done this, you definitely don't need to create a new zone, have you found the installer menu, press and hold the settings button. I can't remember the exact procedure but I remember doing...
  25. Wiring bdr91's into a sundial wiring centre

    So, I have evohome and still use my existing programmer to control the hw, but I do have the hot water kit, just haven't wired it in yet. I used the room stat terminal block to wire in the ch bdr91...
Results 1 to 25 of 40
Page 1 of 2 1 2