Search:

No idea then sorry. I just connected my bridge to the boiler and set the evohome to opentherm and then did the binding.
Might be worth emailing Honeywell about it, they were good when I emailed...

Just looking at the manual for your boiler, you have removed the connector between terminals 6-7 as well as connecting the opentherm to terminals 11 and 12.
And like G4RHL says, once connected a...

If it does connect, it will still say opentherm in the options until you change it. When I setup mine I connected the opentherm bridge to the boiler and when I setup the evohome controller it was...

I am not sure my evohome tells me it is receiving a signal from it. I am sure it just said it had binded to the R8810 receiver and the receiver just started to flash green slowly.
It could be a...

Just checking you have set the evohome system devices option to appliance control opentherm bridge option.

Did you ever sort this out.
I have had the exact same problem with one of our radiators and valves.
The radiator was getting warm all the time even when turned to off.
I found it hard to manually...

When we had the room temp set before smart weather, the room would feel cold on cold days even though it said it was at the correct temp.
Now on cold days the room goes to a slightly higher temp and...

The smart weather seems to work fine for me.
If it is colder outside, the rooms I have it set up on will got to a higher temp to help compensate for the temp outside.
When we had the warm spell,...

Mine has done similar. Last night it set the livingroom to 5 degrees but later it turned it back on. Today it has set a few to 5 degrees but not all.
I am sure this is all part of the smart weather...

So did mine, it just appeared. A quick email with a picture of your controller MAC ID and CRC code will sort it out

There are other posts about phantom zones if you search.
Contact evohome support and they will remove it for you

Are you checking to ensure the HR92 is properly locked into place on the radiator.
I didn’t fully lock the one in my kids room in place and it did not shut off the radiator, so the radiator was...

I have an Ideal combi boiler with evohome opentherm setup and don’t seem to have any problems.
I just connected the opentherm bridge, set up the controller to opentherm and let it do what it wanted,...

We have an opentherm controlled boiler and the optimisation works quite well.
The boiler output seems to be dependent on what the room temp is and I assume how long the system thinks it will take to...

The ghost room does not control anything, that is what I was told. So if you have it, it is not going to do anything but just annoy you.

Just info for the op so they know to email and support will remove it without you having to delete anything.
I had it twice and both times it was removed within a day of me emailing them my...

You need to email to the support department about the ghost zone. They will ask for info from your controller and remove it

Are you sure it is not the frost protection working. I know someone has said that if you turn it to off, frost protection is disabled but the instructions state that it will still work if the heating...

It works on mine, I turned it off and it always is off.

1747
The user guide states that if you turn the HR92 to off it will stay off.
As stated maybe check the batteries, when they are close to dying, my HR92’s tend to go to override at 20c until I...

Looking at my controller, that room is set to 5c and set to permanent and the HR92 always reads off.
Have you set the room to be permanently at 5c on the controller.

I have the one in my spare room set to off, I just turned until it said off and that is where it has stayed.
I don’t believe I did anything on the controller to ensure it stayed in the off position....

Thanks, think I have sorted it now.
I just removed the room/zone and then set it up again.
They all seem to work, just need to see if the radiator stays hot until the DTS91E is reading the...

Hi, Just got a DTS92E for my evohome system to help control the dining room temperature.
Just now I only have HR92 rad valves fitted in every room along with the main controller in the living room...

Cheers, bought a DST92E and will see how it goes before buying more for the other rooms