Search:

Type: Posts; User: StuartP

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    572

    It's looking like a dodgy OT Bridge. Waiting for...

    It's looking like a dodgy OT Bridge. Waiting for the replacement to arrive.

    Update - Issue resolved with a replacement OTB Module.
  2. Replies
    4
    Views
    572

    Opentherm & Intergas

    Hi All,

    Trying to setup Evohome using the opentherm bridge, and my intergas exclusive.

    Pairing of the bridge goes fine. I get a single green flash from the bridge, and then the 3 red flashes,...
  3. Replies
    15
    Views
    2,374

    Details of per-heated solar DHW on an intergas...

    Details of per-heated solar DHW on an intergas boiler
    1797
  4. Replies
    15
    Views
    2,374

    Intergas certainly opens up options, I've toyed...

    Intergas certainly opens up options, I've toyed with a cylinder as you described, but also with a coil taking the CH return into the boiler to further increase the change of the boiler condensing,...
  5. Replies
    9
    Views
    1,399

    I came to the same conclusion, 300 more for a...

    I came to the same conclusion, 300 more for a 10% increase in flow rate. The additional heat recovering is also relatively new, so not as tested as perhaps the rest of Intergas's range. You can if...
  6. Just market it as an update nanoCUL arduino. What...

    Just market it as an update nanoCUL arduino. What people choose to do with it after that is up to them.

    10 for a bare PCB seems a little steep, who are you using as your PCB house ?
  7. Replies
    9
    Views
    1,399

    Went for an Xclusive 36 a couple of months ago,...

    Went for an Xclusive 36 a couple of months ago, can't fault it apart from the fact that the utility room it's in is now colder (no rad in the room), as the boiler is better insulated than the...
  8. I've dropped you a PM as I'm about to replace my...

    I've dropped you a PM as I'm about to replace my TPI boiler interface with OTB.
  9. Replies
    1
    Views
    683

    Evohome, to reset or not

    With a planned replacement of my boiler, and a move to opentherm. Is it best to reset EvoHome and let it learn new characteristics or am I ok simply replacing the TPI controller with opentherm and...
  10. Replies
    217
    Views
    91,373

    For anyone that's interested, there's now a...

    For anyone that's interested, there's now a project by zxdavb to use HGI80 on home assistant, see the following forum thread...
  11. There's already a good understanding of the RF...

    There's already a good understanding of the RF protocol in use, see

    https://www.automatedhome.co.uk/vbulletin/showthread.php?5085-My-HGI80-equivalent-Domoticz-setup-without-HGI80
  12. So, Raspberry Pi + Display + Case, in something...

    So, Raspberry Pi + Display + Case, in something like

    https://cdn.shopify.com/s/files/1/0176/3274/products/102035_1024x1024.jpg?v=1540880922

    Then just a case of adding in the required RF board. ...
  13. Is the touch panel really required ?

    Is the touch panel really required ?
  14. The developer is already on AH Forums as well,...

    The developer is already on AH Forums as well, it's https://www.automatedhome.co.uk/vbulletin/member.php?40264-zxdavb
  15. Certainly interested in going down the python...

    Certainly interested in going down the python route with an HGI, I'm following this closely
    ...
  16. Replies
    2
    Views
    6,946

    Found this in the installer guide for Xtreme and...

    Found this in the installer guide for Xtreme and XClusive boilers.

    1447
  17. Replies
    12
    Views
    3,506

    dty, yup your NodeRed components, took very...

    dty, yup your NodeRed components, took very little time to figure out, more time working out device ID's.

    Would love to be able to start controlling from NodeRed, but getting stuff graphed is the...
  18. Replies
    12
    Views
    3,506

    Got it working, looks great, a bit more tweaking...

    Got it working, looks great, a bit more tweaking of config needed.
  19. Replies
    12
    Views
    3,506

    Ok, so a quick test of the evohome-listener, and...

    Ok, so a quick test of the evohome-listener, and it's not as featured as domoticz. So I'm now wondering is there anyway to get the data from the HGI80 into both domoticz, and evohome-listener.
    ...
  20. Replies
    12
    Views
    3,506

    Thanks for the pointer Dan. Will take a look.

    Thanks for the pointer Dan. Will take a look.
  21. Replies
    12
    Views
    3,506

    Evohome HGI80 MQTT

    Is anyone aware of software that takes info from an HGI80 and publishes as MQTT, looking for logging only at this stage, although longer term MQTT control would be ideal
  22. Replies
    6
    Views
    2,629

    Oversize / Undersize Rads

    As I've got some valves on my evohome based system that need to be replaced, I'm also thinking about replacing some radiators, a like for like replacement is the obvious thing to do, but are there...
  23. Replies
    2
    Views
    1,144

    Historic Weather Data

    Does anyone know of a source for daily / weekly historic weather data (specifically temperature) ?
  24. [For Sale] Z-Wave StellaZ Radiator Thermostat

    Hi,

    I've got 5 brand new Z-Wave StellaZ Radiator Thermostat's for sale.

    https://www.vesternet.com/z-wave-stellaz-radiator-thermostat

    40 inc postage each.

    Thanks
  25. Replies
    6
    Views
    2,077

    Yup, xmas lights are well known for causing RF...

    Yup, xmas lights are well known for causing RF problems, including affecting broadband connections. Back to good old candles I say.
Results 1 to 25 of 81
Page 1 of 4 1 2 3 4