Search:

Type: Posts; User: smar

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    18
    Views
    668

    Thans and will do.

    Thans and will do.
  2. Replies
    18
    Views
    668

    That would be great! No urgency though, as I am a...

    That would be great! No urgency though, as I am a bit tied up with some work at the moment, and may not be able to give much time at the immediate moment, but definitely something worth doing. Please...
  3. Replies
    18
    Views
    668

    Great piece of work @zxdavb! Had I seen yours...

    Great piece of work @zxdavb! Had I seen yours before, I wouldn't have bothered doing the evolistener script, and would have just used yours as the basis for what I need!

    Would you consider hooking...
  4. Replies
    18
    Views
    668

    Hi @Lloyd Device type 12 - this is not defined...

    Hi @Lloyd

    Device type 12 - this is not defined as none of my devices have that type number!

    Zone 252 - this is an internal number hard coded into evohome and is coming from the evohome devices.
  5. Replies
    31
    Views
    2,029

    Yes, I've found it a bit limiting as well. 16 or...

    Yes, I've found it a bit limiting as well. 16 or more would have been perfect.
  6. Replies
    31
    Views
    2,029

    Yes, I'm still getting them. Last one was two...

    Yes, I'm still getting them. Last one was two days ago.
  7. Replies
    60
    Views
    4,546

    Is this also supposed to turn off UFH zones via...

    Is this also supposed to turn off UFH zones via HCC80R? If so, I am not seeing it on my setup, as the UFH zones lights are still on.
  8. Replies
    20
    Views
    2,345

    Fair point and makes sense. Will give it a go and...

    Fair point and makes sense. Will give it a go and see how it pans out. A switch to turn the feature off/on sounds a good idea!
  9. Replies
    20
    Views
    2,345

    Interesting "hack" you are using... Yes, the...

    Interesting "hack" you are using...

    Yes, the reheat time does seem to be too high for an effective hot water priority solution. I have been running without hot water priority since the system was...
  10. Replies
    20
    Views
    2,345

    Thanks and yes, makes sense. Not really sure if...

    Thanks and yes, makes sense. Not really sure if our cylinder would be classifed as a quick re-heat - it is an unvented OSO Powercyl Delta Coil, installed last year. Normally takes about 45 minutes...
  11. Replies
    20
    Views
    2,345

    Yes, I do have the separate zone valves/BDR91s,...

    Yes, I do have the separate zone valves/BDR91s, though I had previously disconnected the one for raditators, and left it in the open position (it had started to stick - even though it was only about...
  12. Replies
    20
    Views
    2,345

    Yes, that is what I had figured. Assuming that I...

    Yes, that is what I had figured. Assuming that I don't have hot water priority, then I'm guessing that some of the benefits would be negated?
  13. Replies
    20
    Views
    2,345

    Thanks and sounds good.

    Thanks and sounds good.
  14. Replies
    20
    Views
    2,345

    Great, thanks. As you've had your OT bridge in...

    Great, thanks. As you've had your OT bridge in place for a few years now, is it something you would recommend based on your experience (I have a Vaillant condensing system boiler, and my DHW is also...
  15. Replies
    20
    Views
    2,345

    I've been thinking about adding OpenTherm to my...

    I've been thinking about adding OpenTherm to my setup. What problems are you encountering with the OT bridge? Is there somewhere where you are discussing this?

    Thanks.
  16. Replies
    84
    Views
    6,724

    I am using an arduino/CC1101 to monitor the...

    I am using an arduino/CC1101 to monitor the messages and simply don't see messages from the CS92A when it stops working. If the issue was controller related, I would have expected the messages to...
  17. Replies
    84
    Views
    6,724

    I'm using the insertion sensor and have the same...

    I'm using the insertion sensor and have the same issues described here. In fact, as advised by Honeywell, I have also put in thermal paste into my cylinder's insertion point, to aid thermal...
  18. Replies
    84
    Views
    6,724

    No, I didn't try that one. May give it a go at...

    No, I didn't try that one. May give it a go at some point but as per @DBMandrake, I also think that there is an inherent design issue with these units.
  19. Yes, the HCC80R. Could you open an issue...

    Yes, the HCC80R.



    Could you open an issue on the github page, and also include the relevant lines from the raw log file. Also that error line number doesn't seem to be correspond to the current...
  20. Here's a couple of lines (filtered out to show...

    Here's a couple of lines (filtered out to show just the 02: messages):

    Raw:

    2020-01-26 08:26:21 |1| ZONE_HEAT_DEMAND --- I --- 02:043392 --:------ 02:043392 3150 006 00AC01BA029C
    2020-01-26...
  21. Replies
    84
    Views
    6,724

    I don't think the update frequency changed with...

    I don't think the update frequency changed with lower differentials for either of the senders. The lower differentials just meant that as and when a measurement was finally sent, evhome would start...
  22. Ok thanks for the confirmation.

    Ok thanks for the confirmation.
  23. @DanD I also just tried the 'fifo-hang' branch....

    @DanD I also just tried the 'fifo-hang' branch. Zone demand data seems to be coming through fine on the HCC80R with this as well, but sending is no longer working for me (arduino nano). Rolling back...
  24. That's actually the way I've done the script -...

    That's actually the way I've done the script - when sending messages, it sends it from that 30: id, so that the evohome controller thinks it is getting a valid instruction from an internet gateway.
  25. I recall when I was testing with one of ghoti's...

    I recall when I was testing with one of ghoti's firmwares (I think the master) I wasn't receiving any messages from my HCC80R. Switching to the other fifo branch, the messages immediately started...
Results 1 to 25 of 57
Page 1 of 3 1 2 3