Search:

Type: Posts; User: mtmcgavock

Page 1 of 17 1 2 3 4

Search: Search took 0.01 seconds; generated 28 minute(s) ago.

  1. Replies
    3
    Views
    410

    Erratic HW behaviour is usually down the the...

    Erratic HW behaviour is usually down the the CS92A rather than the BDR91. Have you tried moving that instead? Or rotating it 90 degrees as DBMandrake suggested in a previous post.

    My BDR91s are...
  2. You can make it work of a basic fashion but not...

    You can make it work of a basic fashion but not how it should, and tbh wonít be very efficient.

    Arenít you thinking of Unvented cylinders? As which thereís a difference between a thermal store and...
  3. Simple answer is Evohome won't work with Thermal...

    Simple answer is Evohome won't work with Thermal Stores.
  4. Replies
    10
    Views
    927

    One of our HR92s is showing low battery but can't...

    One of our HR92s is showing low battery but can't bring myself to change it yet :p

    Was hoping for them to last till September/October then i'm going to change them all to Lithium in one go and see...
  5. Replies
    31
    Views
    1,063

    Yeah when I said remove all Vaillant controls I...

    Yeah when I said remove all Vaillant controls I did mean everything, including the probe.
  6. Replies
    31
    Views
    1,063

    If the tap symbol is on the screen it means the...

    If the tap symbol is on the screen it means the Vaillant controls are still in control - as it's requesting a DHW rapid reheat. With EvoHome you could only ever get a Radiator symbol on the screen as...
  7. Replies
    31
    Views
    1,063

    Did you remove the 24v link? Check that when...

    Did you remove the 24v link? Check that when Green lights are off on BDR91s there's no demand at the boiler.

    Boiler should only run when there's a Green light on the Boiler Relay BDR91.
  8. Replies
    31
    Views
    1,063

    No not really, in fact it's better doing it your...

    No not really, in fact it's better doing it your way - I do this sometimes and just crank the stat to max (So 65oc in your case) but it's depending on how high the regular stat will set and what you...
  9. Replies
    31
    Views
    1,063

    No that diagram isn't correct. So the stat on...

    No that diagram isn't correct.

    So the stat on the side of the cylinder - is the dual stat. You need to connect B from you BDR91 to C on the lefthand side stat (this is the High Limit stat). Then...
  10. Replies
    31
    Views
    1,063

    No the existing cylinder stat must stay in place...

    No the existing cylinder stat must stay in place as this is a Dual stat. High limit and a cylinder stat. If the cylinder stat was to fail then the high limit stat would click in cutting the power to...
  11. Replies
    31
    Views
    1,063

    First attachment isn't working. Second...

    First attachment isn't working.

    Second diagram is correct.

    Yes, N and E from Zone valves can go to Fuse Spur. Orange and Grey wires can be left disconnected.

    DHW to sort then.
  12. Replies
    31
    Views
    1,063

    I did remove the Bus connector but did not remove...

    I did remove the Bus connector but did not remove the receiver from the front when i tested last night, will give it another go with that removed, again, thank you
    With the receiver still in the...
  13. Replies
    31
    Views
    1,063

    You can't use eBus with Evohome only the S/L on...

    You can't use eBus with Evohome only the S/L on RT230v.

    Firstly you'll have to remove all the Vaillant Controls, so remove the eBus wiring and the wireless receiver for the 470f out the front of...
  14. Replies
    31
    Views
    1,063

    Yes I have, however i'm just on my way out and...

    Yes I have, however i'm just on my way out and need to sit down and read your full post and think about things. So i'll reply sometime in the near future. Unless you've worked it out?
  15. This shouldn't be happening, even with just a HW...

    This shouldn't be happening, even with just a HW demand. There's either something not configured correctly in the settings (Just read you've set the flow at 55oc when cylinder is at 50oc) or there's...
  16. Replies
    4
    Views
    372

    Think you'll find the majority have Evohome on...

    Think you'll find the majority have Evohome on here. There's the odd one with Drayton Wiser. Think the majority came to the same conclusion of that Evohome was the better system, or had it before any...
  17. Replies
    8
    Views
    440

    I leave my flow set at around 70oc all year...

    I leave my flow set at around 70oc all year round. Higher flow temp for HW, quicker reheat time.
  18. I'm suffering with this too and could do with a...

    I'm suffering with this too and could do with a new beta/update coming through. Actually struggling more with this after turning the heating off as we manually boost zones.
  19. Be interesting to see how long your new head...

    Be interesting to see how long your new head lasts for. As I said in my earlier post been having a lot of issues with the Honeywell valves failing of recent. One where it got stuck open on an...
  20. Replies
    19
    Views
    1,529

    As others have said, I use Custom Action renamed...

    As others have said, I use Custom Action renamed as Summer. All zones set to 16oc, with set points throughout the day so if one does get overridden locally it'll take it back down to 16oc.
    ...
  21. I was more thinking of just an updated Evohome...

    I was more thinking of just an updated Evohome panel :rolleyes: But I guess software updates keep it current.
  22. Out of interest, is there any new...

    Out of interest, is there any new hardware/updates coming soon?
  23. Replies
    4
    Views
    205

    Cheers, PM Sent :D

    Cheers, PM Sent :D
  24. Replies
    4
    Views
    205

    Any chance you'd be will to send one out for a...

    Any chance you'd be will to send one out for a fee in return? :)
  25. Replies
    4
    Views
    205

    Face Plates - anyone got any spare?

    So after reading the other day on another thread about the controller being loose on the wall plate, I thought that mines never fallen off. Well today it happened whilst decorating, slightly knocked...
Results 1 to 25 of 419
Page 1 of 17 1 2 3 4