Search:

Type: Posts; User: raven

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    8,442

    Automation takes virtually no processing power so...

    Automation takes virtually no processing power so you could run it on a 10 year old computer. However, CCTV may take up a lot more depending on your setup. If you have two or more megapixal network...
  2. Replies
    15
    Views
    10,952

    As Toscal mentioned you need this...

    As Toscal mentioned you need this http://www.letsautomate.com/10215.cfm?CFID=1460957&CFTOKEN=956B6F2E-83D9-4F0A-86DE02B6ADF4840A to allow you visonic to talk x10.

    Then you need some switches. Try...
  3. Replies
    15
    Views
    10,952

    Ok, I have used a Visonic PIR sensor (just a...

    Ok, I have used a Visonic PIR sensor (just a normal indoor wireless one) placed in a water proof tube with a small whole in it nailed to a tree. A waterproof bird box would be a good choice. The...
  4. Replies
    15
    Views
    10,952

    Hey just read this thread and I have a very...

    Hey just read this thread and I have a very similar setup.

    I have powermax+ with X10 interface although I mainly use PLCBus with an X10/PLCBUS repeater.
    An iqeye camera
    An outside infrared...
  5. Replies
    2
    Views
    2,091

    It is an exit/entry zone and the manual did imply...

    It is an exit/entry zone and the manual did imply it would bypass the zone (as the option suggests) although "force arm" seemed to be along the right lines. I obvioulsy don't want to bypass the zone...
  6. Does it use a USB or serial interface?

    Does it use a USB or serial interface?
  7. Replies
    2
    Views
    2,091

    powermax+ Force arm

    It it possible to force the system to arm even though a door is open.

    I would like to be able to arm the system even though I have left the front door open.

    The option "bypass" seems to be the...
  8. Replies
    5
    Views
    4,354

    You may find the problem is the usb block (The...

    You may find the problem is the usb block (The little block half way up the lead.) that converts the usb lead to rs232. I had a similar problem with mine. To confirm unplug the usb lead from the...
  9. Sorry for the delay in replying. The problem...

    Sorry for the delay in replying.

    The problem with the test circuit is that it is not like for like. For instance there is no load on the device so perhaps that's important. The problem is the time...
  10. Update

    I've now confimred it is not the switch leads as I disconnected them and used an X10 module to control the light. It locked up last night so now I've tried about 10 foot of cable to see if that has...
  11. Replies
    5
    Views
    3,277

    I have connected zones 29 and 30 to wired devices...

    I have connected zones 29 and 30 to wired devices on my powermax+. Do you still need help?
  12. Thanks for the ideas. When I turn either the...

    Thanks for the ideas.

    When I turn either the bathroom light off (or on) or my bedroom light off or on the X10 module in question may crash - i.e. It goes off never to come on without a power...
  13. Thanks for the full reply. Answers: 1: The...

    Thanks for the full reply.

    Answers:

    1: The landing light is two 15w-ish energy efficient bulbs.
    2: Via the switch wires plus a CM?? controller thingy.
    3: A3.
    4: All my lights are...
  14. One Load Appliance Micro Module from automated@home locks up

    I have purchased the "One Load Appliance Micro Module" (X10-2267) from automated@home and all works ok or at least until it locks up. The device controls my landing light. I've noticed that when I...
Results 1 to 14 of 14