Search:

Type: Posts; User: Somebody

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Hi, count me in for an assembled unit please.

    Hi, count me in for an assembled unit please.
  2. You need to do some reading.... ...

    You need to do some reading....

    https://community.smartthings.com/t/faq-request-installing-custom-device-type-device-handler-smartapp/11258
  3. Assuming you have Smartthings? In your IDE,...

    Assuming you have Smartthings? In your IDE, install and publish the app and device handler from the the gitbub link above (the first and third item). Log in with your Honeywell credentials in the...
  4. Follow this for the 2020 new smartthings app...

    Follow this for the 2020 new smartthings app integration: https://community.smartthings.com/t/release-honeywell-evohome-2020-integration-with-new-smartthings-app

    I had the old Codersaur code...
  5. I have Evohome integrated with Samsung...

    I have Evohome integrated with Samsung Smartthings, with a routine which does exactly as you describe which is to turn on Eco mode when everyone leaves (in the morning).
  6. I picked up a Center 340009 on eBay, which is a...

    I picked up a Center 340009 on eBay, which is a cheaper alternative. https://www.wolseley.co.uk/product/center-rf-non-programmable-room-thermostat/

    Also known as EHE0200364. There's a new one on...
  7. Nope. Currently you cannot set a time schedule...

    Nope.
    Currently you cannot set a time schedule to the commands. Zone commands to evohome Wi-Fi and Single Zone Thermostat will operate until the next schedule. For example, you cannot say “Alexa...
  8. @robbietobbie Do you have Alexa? There's...

    @robbietobbie Do you have Alexa? There's integration with Alexa and I ask Alexa to turn up the temperature in that room, which Evohome will keep until the next set point. I have a set point at...
  9. Talking of TPI, I assume this TPI in action from...

    Talking of TPI, I assume this TPI in action from 18:45 onwards?

    https://i.imgur.com/WjpdWPJm.jpg

    TIA
  10. Happened to me after 4 months following...

    Happened to me after 4 months following installation. Shot up to 66 degrees C. Showed the temp graphs to my installer who replaced the probe that goes to the cylinder and it's been fine since. So...
  11. Replies
    9
    Views
    1,335

    Are you on the beta firmware? I'm not on beta,...

    Are you on the beta firmware? I'm not on beta, and don't see an icon; only a message:

    https://i.imgur.com/nDVy92Wm.jpg
  12. Replies
    8
    Views
    1,236

    I have these probes shoved down the foam...

    I have these probes shoved down the foam insulation which wraps around the flow and return pipes above my boiler:...
  13. Thread: Ifttt

    by Somebody
    Replies
    9
    Views
    1,233

    Test email works. I donít understand why...

    Test email works. I donít understand why Notifications donít.
  14. Thread: Ifttt

    by Somebody
    Replies
    9
    Views
    1,233

    Although set up, I never receive emails from...

    Although set up, I never receive emails from Domoticz.

    https://i.imgur.com/x9L4SFu.png

    What's the trick, bruce?
  15. Replies
    2
    Views
    1,781

    I have Samsung Smartthings and added...

    I have Samsung Smartthings and added (non-Samsung) smoke and gas detectors which sound and also notify via the app when triggered.

    https://i.imgur.com/5vKwEP6l.jpg
    ...
  16. Replies
    4
    Views
    1,080

    Good point, G4RHL. My kids are nocturnal and...

    Good point, G4RHL. My kids are nocturnal and they have a tendency to up their room temps in the early hours so when they're back from uni I have to set the first time slot from 00:00 to 03:00 for...
  17. Replies
    4
    Views
    1,080

    Are you sure you want on/off sequence rather than...

    Are you sure you want on/off sequence rather than the number of temperature set points during the day? What system are you talking about?

    In Evohome there are are 6 set points available for each...
  18. Replies
    84
    Views
    9,479

    It could be the temperature sensor/probe itself...

    It could be the temperature sensor/probe itself i.e. the temp sensor that connects by wire to the CS92A? My probe was reading 66 degrees C 4 months after a new install.
    ...
  19. Replies
    455
    Views
    64,278

    Got the same email. Yes, untrue. Servers down...

    Got the same email. Yes, untrue. Servers down since 1am according to my Domoticz set up.
  20. Replies
    12
    Views
    2,178

    Drill down to the next level?...

    Drill down to the next level?
    https://i.imgur.com/BorcORb.jpg
  21. Replies
    14
    Views
    2,737

    If it ain't broke, don't fix it?!? It's a...

    If it ain't broke, don't fix it?!? It's a mature, solid, first class functional product that others are trying to re-invent. What additional functionality are you looking for?
  22. Replies
    12
    Views
    2,178

    Can be found under a resideo.com subdomian: ...

    Can be found under a resideo.com subdomian:
    https://homecomfort.resideo.com, under Products > Home Comfort > Zoning control
  23. You're supposed to turn the black ring fully...

    You're supposed to turn the black ring fully anticlockwise
    https://ensupport.getconnected.honeywellhome.com/s/article/How-to-install-the-HR92-Radiator-Controller?language=en_US
  24. Replies
    1
    Views
    2,535

    Have a look here:...

    Have a look here: http://codersaur.com/2016/04/smartthings-data-visualisation-using-influxdb-and-grafana/ and...
  25. Replies
    7
    Views
    1,416

    I have Smartthings which I integrated with...

    I have Smartthings which I integrated with Evohome. Using various tutorials I was able to chart the the heating/idle times of the zones:

    https://i.imgur.com/fW1zV4ym.jpg
Results 1 to 25 of 36
Page 1 of 2 1 2