Search:

Type: Posts; User: DBMandrake

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds; generated 26 minute(s) ago.

  1. Replies
    47
    Views
    6,284

    If you want alerts to your phone when batteries...

    If you want alerts to your phone when batteries are low you're going to need to use something 3rd party like Home Assistant talking directly to the controller over its 868Mhz protocol with a suitable...
  2. There's no delete button that clears all device...

    There's no delete button that clears all device bindings from a zone that I'm aware of, unless you're thinking of deleting the entire zone and re-adding it, but that's going to erase the schedule as...
  3. If only! There are no magnets in the wall...

    If only!

    There are no magnets in the wall mount or controller on a Gen3 - in fact it sits very loosely in the wall mount with no resistance to sliding up except its own weight.

    This means it is...
  4. Given the catastrophe that a genuinely freezing...

    Given the catastrophe that a genuinely freezing hot water cylinder in an unoccupied house would result in (especially if mounted in the loft space) I think it's prudent to let the frost protection do...
  5. If it's a problem with the rooms using HR80's you...

    If it's a problem with the rooms using HR80's you could always fit a remote temperature sensor. Then you don't need to muck around with offsets.

    I have all HR92's but several of my rooms have...
  6. Replies
    17
    Views
    2,327

    False heat demands from HR92's is usually fixed...

    False heat demands from HR92's is usually fixed by doing a reboot of the HR92 - eg take the batteries out and put them back!

    For me the problem is more often that it sends out a zero heat demand...
  7. Replies
    27
    Views
    4,320

    That would be a case of failing to read the...

    That would be a case of failing to read the manual.... ;)

    The "Heating Off" action does exactly what it says on the tin - it turns off the heating but leaves the hot water schedule running.

    Use...
  8. Replies
    5
    Views
    1,534

    If you have stroke mode set to 1 in the HR92's,...

    If you have stroke mode set to 1 in the HR92's, and they are reporting valve position 0% in option 10 (fully closed) and the radiator is still continuing to heat up then your valve bodies are either...
  9. Replies
    3
    Views
    1,237

    It won't be the HR92's to blame - they can't...

    It won't be the HR92's to blame - they can't cause a knocking noise.

    However they do make very fine adjustments compared to regular manual wax pellet TRV's, and also hold their position constant...
  10. Replies
    12
    Views
    3,486

    Did you have load scaling on Normal or Partial ?...

    Did you have load scaling on Normal or Partial ?

    I find Normal too aggressive, (zones struggling to make their temperatures as you report) but partial works just nicely for me and helps avoid room...
  11. Could one of the switches in your zone valves be...

    Could one of the switches in your zone valves be faulty ? (Leakage due to burnt contacts maybe ?)

    I assume from your diagram you don't have a dedicated boiler relay but just have the two switches...
  12. Short answer is no, you can't do what you're...

    Short answer is no, you can't do what you're trying to do. In a multi-zone Evohome installation every zone must have an actuator, you can't just have a zone with a temperature sensor and no actuator....
  13. If an update happened and you saw the control...

    If an update happened and you saw the control panel within about 30 minutes of that then yes you'd have egg timers for many zones.

    Egg timers for many zones at once means either the device has...
  14. Thread: BDR91 Fault

    by DBMandrake
    Replies
    1
    Views
    1,187

    If there's no lights at all even when you press...

    If there's no lights at all even when you press and hold the button it sounds like it's dead I'm afraid!

    My three have been going 6 years now without any problems so I think you're just unlucky.
  15. Correct, Away mode disables hot water completely....

    Correct, Away mode disables hot water completely.

    You say your system was scheduled to be "off" but later you say your Away mode is configured to 18.5C.

    Clearly that is not "off". It's...
  16. Haven't heard of them. What do they do ? Is it...

    Haven't heard of them. What do they do ?

    Is it similar to Home Assistant ?
  17. Replies
    12
    Views
    2,698

    I assume you haven't read my thread on this...

    I assume you haven't read my thread on this issue:

    https://www.automatedhome.co.uk/vbulletin/showthread.php?5671-Honeywell-Valencia-problems

    I installed Valencia's and same as you found they...
  18. Replies
    4
    Views
    1,024

    There's no way to read the hot water set point...

    There's no way to read the hot water set point through the Honeywell Web API's, the only information made available is the currently measured temperature and whether the hot water schedule is...
  19. Replies
    19
    Views
    3,817

    Same here. We just turn off all our downstairs...

    Same here.

    We just turn off all our downstairs zones at night (5C in the schedule) and rely on Optimal start to figure out when to turn them back on again to reach the target temperatures at the...
  20. Replies
    6
    Views
    1,484

    Alkalines in my DTS92 seem to last a couple of...

    Alkalines in my DTS92 seem to last a couple of years.

    They do have problems with the battery contacts though, if you thump it on the side and it reboots you might need to check the tension of the...
  21. The harsh reality that nobody really wants to...

    The harsh reality that nobody really wants to admit to is that without installing something like an automatic tempering valve (which is typically best done on each hot water outlet) there is no one...
  22. Replies
    4
    Views
    1,394

    I tested an HR91 sample when they first launched...

    I tested an HR91 sample when they first launched but one of the reasons I returned it was this issue - the stroke is insufficient for some valve bodies and there is no Stroke 1 equivalent setting...
  23. Replies
    11
    Views
    1,938

    If an HR92 is not generating any heat demand,...

    If an HR92 is not generating any heat demand, reboot it by removing and reinstalling the batteries.

    It's an occasional glitch in the firmware of the HR92, I've seen it maybe half a dozen times in...
  24. Replies
    5
    Views
    7,377

    Or a new source of RF interference. Added any...

    Or a new source of RF interference.

    Added any new devices around the house recently ?
  25. Replies
    6
    Views
    1,969

    I only have an Evohome system so I don't know....

    I only have an Evohome system so I don't know. Give it a try! It will either work or not. I use the watchforstock Python client bindings - they work with both API's.

    The only benefit in the V1...
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4