Search:

Type: Posts; User: bruce_miranda

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. What do people feel is a better solution for...

    What do people feel is a better solution for devices that track an error code? Keep it at the last error code until the next one or reset the error code, if the error gets reset. With the first...
  2. Ah yes, I can see why, its an issue with the way...

    Ah yes, I can see why, its an issue with the way Domoticz works. To get around that, I think it might be better to just log everything, so that way you know for a fact that a 0 error code has been...
  3. Dont worry, the error code is tracked into a...

    Dont worry, the error code is tracked into a device. If you dont see a device that means you have no Error code. I create devices only for messages that have a non zero value. This way the database...
  4. My changes are now in the main development branch...

    My changes are now in the main development branch of Domoticz, so if you update your code and recompile it, you will get them.
  5. Replies
    40
    Views
    925

    Just make sure you don't have a Zone Valve on the...

    Just make sure you don't have a Zone Valve on the CH that shuts off before even the first radiator. That's when the bypass is really needed.
  6. Completely understand. However you have just...

    Completely understand. However you have just shown me that on some boilers the OTB is able to read and display the DHW Temperatures too.
  7. You definitely have a problem with your radio and...

    You definitely have a problem with your radio and it's firmware. This log has some Heat Demand but again only for 1 UFH controller and only for 1 zone within it.
  8. The weird thing is that there were absolutely NO...

    The weird thing is that there were absolutely NO messages from your UFH controller in the dump that you added earlier. I don't know over what time period that dump was taken but I would have expected...
  9. Yes my entire house is heated all day but to...

    Yes my entire house is heated all day but to about 17C, except the Study which goes to 20C. I wanted to know if this was the most efficient way to deal with my single occupancy during the day or...
  10. I guess I will have to work out how much gas I...

    I guess I will have to work out how much gas I use up during the day to keep the Study heated. And then work out how much it would cost to run an Electric heater for that time. But then also add some...
  11. Run a single radiator using Evohome or invest in an electric radiator

    During the week, I work from home and have the heating just to heat the Study. Evohome does a good job of heating just a single room. But would it be better to turn the entire heating system off and...
  12. The comms between the OTB and the CTL over radio...

    The comms between the OTB and the CTL over radio consists of 5 messages.

    1. Every 30 seconds increment counter.
    2. Every 60 seconds Boiler Relative Modulation and Flame Status.
    3. Every 5...
  13. I would really like to see the System Summary...

    I would really like to see the System Summary screen on your Evohome controller.
  14. Thanks for that. My latest code changes now no...

    Thanks for that. My latest code changes now no longer simply display these messages on the Status Log, but actually make these into devices that are updated as the messages come in. That then allows...
  15. There are some 03: messages here that I have...

    There are some 03: messages here that I have never seen before. Do you have an external temperature sensor on the older V2 Evohome?

    From your message, you appear to have 1 x Controller, 1 x BDR91...
  16. Good question. Which is the message that goes...

    Good question. Which is the message that goes between the OTB and the Boiler that shows the FlameOn Status? Relative Modulation comes back to the evohome controller via two messages, once every 5...
  17. @smar could you help us develop our understanding...

    @smar could you help us develop our understanding about the UFH controller messages. Between a few of us we have practically every bit of Evohome kit EXCEPT an UFH controller. Would you either jump...
  18. Just checked and Domoticz and it doesn't look...

    Just checked and Domoticz and it doesn't look like Domoticz has been updated to handle the array of devices that contain the Heat Demand for a 02: device. But I might be wrong, maybe Dan can confirm....
  19. Do you know anyone who has a HGI80, because at...

    Do you know anyone who has a HGI80, because at the moment, we cannot tell if your NanoCUL isnt decoding the radio signals of the HCE80 or indeed the HCE80 radio messages arent being decoded correctly...
  20. You can also try the fifo branch but from my repo...

    You can also try the fifo branch but from my repo and this compiles in Arduino for the NanoCUL.

    https://github.com/brucemiranda/evofw2/tree/fifo?files=1
  21. The controller queries the OTBridge ever minute...

    The controller queries the OTBridge ever minute and the OTBridge responds with the Boilers Relative Modulation Percentage and the FlameOn Status. As soon as you put the OTGW onto the OT Bus, even in...
  22. Could you make a new thread for this UFH...

    Could you make a new thread for this UFH controller issue. In a few years no one will find it here.
  23. Long Press the Settings icon and show us what the...

    Long Press the Settings icon and show us what the System Summary page looks like on your controller.
  24. There are a bunch of us trying to get a DIY...

    There are a bunch of us trying to get a DIY hardware solution to be reliable. At the moment, none are unfortunately and if you have an OTB then the DIY solutions are pretty bad. In any case you dont...
  25. My code changes are now also able to track if the...

    My code changes are now also able to track if the boiler flame is ON or OFF and that is reported on Domoticz too.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4