Search:

Type: Posts; User: lloyd

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    483

    I presume then that the battery contacts are not...

    I presume then that the battery contacts are not soldered to the PCB?

    I've not looked at disassembling - is it straight forward?
  2. Replies
    6
    Views
    483

    Thanks - as I expected. Also, on the last...

    Thanks - as I expected.

    Also, on the last change, it did not display the Sync message. It's working as a thermostat, but I can't use it to adjust target temperature.

    Think I might be...
  3. Replies
    6
    Views
    483

    DTS92E - Battery Life

    Would anyone with a DTS92E thermostat like to comment on the battery life they experience? I changed the last set about two months ago (Energizer Max), and the unit is already flashing low battery....
  4. Thread: X-Plan

    by lloyd
    Replies
    11
    Views
    1,170

    Ok so this is where my complete lack of knowledge...

    Ok so this is where my complete lack of knowledge of OpenTherm (and perhaps naivety about evohome) shows. I had assumed, probably wrongly, that if you were using OT with evohome, then evohome would...
  5. Thread: X-Plan

    by lloyd
    Replies
    11
    Views
    1,170

    Presumably the temperature sensor connected to...

    Presumably the temperature sensor connected to the boiler is not needed if you have evohome controlling the DHW.
  6. Thread: X-Plan

    by lloyd
    Replies
    11
    Views
    1,170

    ok. I had assumed that if you were using...

    ok. I had assumed that if you were using OpenTherm then evoHome would simply open the CH / DHW valves as appropriate, and if you had enabled DHW priority that it would then always close the CH valve...
  7. Thread: X-Plan

    by lloyd
    Replies
    11
    Views
    1,170

    Thanks for those. Makes for interesting reading. ...

    Thanks for those. Makes for interesting reading.

    One thing I'm still struggling to get my head around is why you need to have the CH 2-port normally open. Is it not more accurate to say that you...
  8. Thread: X-Plan

    by lloyd
    Replies
    11
    Views
    1,170

    X-Plan

    I've seen a few references in various posts regarding a so called x-plan, but any links associated with the conversations lead to 404 errors. Can anyone point me to an explanation or diagram?
  9. Replies
    7
    Views
    804

    Having just moved from Y-plan to S-plan, I'm...

    Having just moved from Y-plan to S-plan, I'm noticing short cycling more now, mainly because the time delay between relay switch on and boiler ignition is longer due to valve delay. Before adding...
  10. Replies
    3
    Views
    455

    Agree. In my mind the system summary is showing...

    Agree. In my mind the system summary is showing demand for each zone and the dhw. The heat relay does not have it's own demand.
  11. Differential 3 degrees, overrun 0 minutes

    Differential 3 degrees, overrun 0 minutes
  12. Replies
    0
    Views
    473

    Updated Honeywell Total Connect Android App

    Got an update to the Honeywell Total Connect Android app today (v4.15.0). Before you get excited, no significant changes.
  13. DHW turned off whilst below target temperature

    Have just installed the DHW side of my Evohome, and noticed yesterday that the relay was turned off for about 10 minutes during the water heating period, way before target temperature was reached. ...
  14. Replies
    108
    Views
    16,262

    You may not get the confirmation you need. ...

    You may not get the confirmation you need. Having just replaced my old cylinder with an unvented one (Joules), I have inserted temperature probe into the thermostat pocket. Modern cylinders are...
  15. Replies
    5
    Views
    1,560

    Evohome - Boiler firing with no demand

    Why is it that even after the demand for heat has fallen to zero, minutes later my boiler is asked to fire? At best this is wasting money, and in the worst case scenario there is a danger of the...
  16. Deleted the zone yesterday, put it back, and this...

    Deleted the zone yesterday, put it back, and this morning that zone only called for heat 45mins before the scheduled set point, and it hit that about 5mins early. I'll monitor over the next few days.
  17. Thanks. I think I agree with the above. This...

    Thanks. I think I agree with the above.

    This is the graph for this morning

    1786

    Green - scheduled SP
    White (dashed) - SP sent to HR91
    Blue & Orange -two HR91 temperatures
    Orange and Blue...
  18. Evohome - excessive use of optimise start period

    I'm currently wondering why I'm seeing at least one, perhaps two, zones which seem to always come on right at the start of their optimisation period first thing in the day. I have had this set to 2...
  19. Replies
    2
    Views
    843

    There is a certain amount you can do without any...

    There is a certain amount you can do without any additional hardware, it just communicates via the web api. https://www.home-assistant.io/integrations/evohome/

    Detailed info I get by listening to...
  20. Replies
    4
    Views
    1,229

    Thanks for that info. Interestingly I'm not...

    Thanks for that info. Interestingly I'm not seeing the announcement when I remove and replace the batteries in my DT92E. This is the sequence I see:


    2021-01-06T17:25:00.067202 || THm:008820 |...
  21. Replies
    4
    Views
    1,229

    DT92E Protocol - battery status

    Does anyone know if a DT92E transmits its battery status at any time, and if it does, is it encoded the same way as other devices such as HR91/2? I've yet to see a battery status from mine, but I'm...
  22. Replies
    6
    Views
    1,697

    Looks like 2020.12.1, released today, has...

    Looks like 2020.12.1, released today, has resolved this.
  23. Replies
    6
    Views
    1,697

    There appears to have been a very similar issue...

    There appears to have been a very similar issue back in 2018:

    https://github.com/home-assistant/core/issues/17851
  24. Replies
    6
    Views
    1,697

    I assume that you are running the current version...

    I assume that you are running the current version of HA?
  25. Replies
    6
    Views
    1,697

    evohome HA clear_zone_override service

    Anyone using the Evohome clear_zone_override service in an automation in Home Assistant? Although I can get this to work in the developer tools, as a newbie I'm struggling with the syntax required...
Results 1 to 25 of 69
Page 1 of 3 1 2 3