Probe Temp Sensing

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts
  • FrankMcAlinden
    Automated Home Guru
    • Feb 2004
    • 109

    Probe Temp Sensing

    Hi All
    Just thought i would mention that i have been working on a temp sensing probe using the Dallas 1820 temp sensor...The idea is to be able to connect a dallas ds1820 to either probe5 or probe 6 of a Probe Zone Box .

    The Probe system detects if a temp sensor is connected to probe 5 or 6 on any of the 8 zones and reports the temp (currently .5 degree tolerence) via the serial interface in reponse to a status request....

    Still some more testing to do as im not sure what length of cat5 this will reliably work on..But if it works it means that i can free up one cat5 cable per room which is currently used for temp sensors...as i have a probe zone box in each room at present monitoring tv,s and dvd players etc....

    More Soon
    Frank
    Home of FirM - the Multi Zone IR Transport System
    http://www.armaghelectrical.com.au/index.html
  • Otto-Mate
    Founder
    • Jan 2004
    • 882

    #2
    Re: Probe Temp Sensing

    Sounds interesting Frank. Keep us informed!

    M.
    Editor AutomatedHome.co.uk


    www.facebook.com/AutomatedHomeUK
    www.twitter.com/ottomate
    www.instagram.com/automatedhome/

    Comment

    • FrankMcAlinden
      Automated Home Guru
      • Feb 2004
      • 109

      #3
      Re: Probe Temp Sensing

      Sounds interesting Frank. Keep us informed!

      Will do ...Its looking good , have a test sensor connected to 50m of cat5 cable and its working fine ..just need to order some ds 18s20 sensors and install them....these are 9 bit sensors and later i might have a look at incorporating the ds18b20 which is a 12 bit sensor......

      More Soon
      Frank
      Home of FirM - the Multi Zone IR Transport System
      http://www.armaghelectrical.com.au/index.html

      Comment

      • FrankMcAlinden
        Automated Home Guru
        • Feb 2004
        • 109

        #4
        Re: Probe Temp Sensing

        Just a little update...
        Have now installed several sensors around the house and also on my test Probe system....Im using xPL to read the status of the temp sensors (ds18s20) every 15 minutes and its all working quite well...

        Im comparing the readings against the TOM10 temp sensors and they are normally within 1 degree C ....

        I had 2 sensors connected to my test Probe system and they were approx 4 inches apart and there was 1 degree C difference in temp....I have now tied them together and now they both read the same temp ....maybe explains why Im getting different readings between the TOM10 and my Probe temp sensors.

        Frank
        Home of FirM - the Multi Zone IR Transport System
        http://www.armaghelectrical.com.au/index.html

        Comment

        • Otto-Mate
          Founder
          • Jan 2004
          • 882

          #5
          Re: Probe Temp Sensing

          Sounds good, any pics Frank?

          M.
          Editor AutomatedHome.co.uk


          www.facebook.com/AutomatedHomeUK
          www.twitter.com/ottomate
          www.instagram.com/automatedhome/

          Comment

          • FrankMcAlinden
            Automated Home Guru
            • Feb 2004
            • 109

            #6
            Re: Probe Temp Sensing

            Hi Mark
            Sounds good, any pics Frank?

            No not as yet im waiting until i can get a suitable housing for the sensors , ill take some then.......

            Frank
            Home of FirM - the Multi Zone IR Transport System
            http://www.armaghelectrical.com.au/index.html

            Comment

            Working...
            X